VirtualAllocEx
Last updated
Last updated
[in] hProcess
The handle to a process. The function allocates memory within the virtual address space of this process.
The handle must have the PROCESS_VM_OPERATION access right. For more information, see Process Security and Access Rights.
[in, optional] lpAddress
The pointer that specifies a desired starting address for the region of pages that you want to allocate.
If you are reserving memory, the function rounds this address down to the nearest multiple of the allocation granularity.
If you are committing memory that is already reserved, the function rounds this address down to the nearest page boundary. To determine the size of a page and the allocation granularity on the host computer, use the GetSystemInfo function.
If lpAddress is NULL, the function determines where to allocate the region.
If this address is within an enclave that you have not initialized by calling InitializeEnclave, VirtualAllocEx allocates a page of zeros for the enclave at that address. The page must be previously uncommitted, and will not be measured with the EEXTEND instruction of the Intel Software Guard Extensions programming model.
If the address in within an enclave that you initialized, then the allocation operation fails with the ERROR_INVALID_ADDRESS error. That is true for enclaves that do not support dynamic memory management (i.e. SGX1). SGX2 enclaves will permit allocation, and the page must be accepted by the enclave after it has been allocated.
[in] dwSize
The size of the region of memory to allocate, in bytes.
If lpAddress is NULL, the function rounds dwSize up to the next page boundary.
If lpAddress is not NULL, the function allocates all pages that contain one or more bytes in the range from lpAddress to lpAddress+dwSize. This means, for example, that a 2-byte range that straddles a page boundary causes the function to allocate both pages.
[in] flAllocationType
The type of memory allocation. This parameter must contain one of the following values.
MEM_COMMIT0x00001000
Allocates memory charges (from the overall size of memory and the paging files on disk) for the specified reserved memory pages. The function also guarantees that when the caller later initially accesses the memory, the contents will be zero. Actual physical pages are not allocated unless/until the virtual addresses are actually accessed.
To reserve and commit pages in one step, call VirtualAllocEx with MEM_COMMIT | MEM_RESERVE.
Attempting to commit a specific address range by specifying MEM_COMMIT without MEM_RESERVE and a non-NULL lpAddress fails unless the entire range has already been reserved. The resulting error code is ERROR_INVALID_ADDRESS.
An attempt to commit a page that is already committed does not cause the function to fail. This means that you can commit pages without first determining the current commitment state of each page.
If lpAddress specifies an address within an enclave, flAllocationType must be MEM_COMMIT.
MEM_RESERVE0x00002000
Reserves a range of the process's virtual address space without allocating any actual physical storage in memory or in the paging file on disk.
You commit reserved pages by calling VirtualAllocEx again with MEM_COMMIT. To reserve and commit pages in one step, call VirtualAllocEx with MEM_COMMIT | MEM_RESERVE.
MEM_RESET0x00080000
Indicates that data in the memory range specified by lpAddress and dwSize is no longer of interest. The pages should not be read from or written to the paging file. However, the memory block will be used again later, so it should not be decommitted. This value cannot be used with any other value.
Using this value does not guarantee that the range operated on with MEM_RESET will contain zeros. If you want the range to contain zeros, decommit the memory and then recommit it.
When you use MEM_RESET, the VirtualAllocEx function ignores the value of fProtect. However, you must still set fProtect to a valid protection value, such as PAGE_NOACCESS.
VirtualAllocEx returns an error if you use MEM_RESET and the range of memory is mapped to a file. A shared view is only acceptable if it is mapped to a paging file.
MEM_RESET_UNDO0x1000000
MEM_RESET_UNDO should only be called on an address range to which MEM_RESET was successfully applied earlier. It indicates that the data in the specified memory range specified by lpAddress and dwSize is of interest to the caller and attempts to reverse the effects of MEM_RESET. If the function succeeds, that means all data in the specified address range is intact. If the function fails, at least some of the data in the address range has been replaced with zeroes.
This value cannot be used with any other value. If MEM_RESET_UNDO is called on an address range which was not MEM_RESET earlier, the behavior is undefined. When you specify MEM_RESET, the VirtualAllocEx function ignores the value of flProtect. However, you must still set flProtect to a valid protection value, such as PAGE_NOACCESS.
Windows Server 2008 R2, Windows 7, Windows Server 2008, Windows Vista, Windows Server 2003 and Windows XP: The MEM_RESET_UNDO flag is not supported until Windows 8 and Windows Server 2012.
This parameter can also specify the following values as indicated.
MEM_LARGE_PAGES0x20000000
If you specify this value, you must also specify MEM_RESERVE and MEM_COMMIT.
MEM_PHYSICAL0x00400000
This value must be used with MEM_RESERVE and no other values.
MEM_TOP_DOWN0x00100000
Allocates memory at the highest possible address. This can be slower than regular allocations, especially when there are many allocations.
[in] flProtect
The memory protection for the region of pages to be allocated. If the pages are being committed, you can specify any one of the memory protection constants.
If lpAddress specifies an address within an enclave, flProtect cannot be any of the following values:
PAGE_NOACCESS
PAGE_GUARD
PAGE_NOCACHE
PAGE_WRITECOMBINE
When allocating dynamic memory for an enclave, the flProtect parameter must be PAGE_READWRITE or PAGE_EXECUTE_READWRITE.
Other memory allocation functions, such as malloc and , cannot use reserved memory until it has been released.
Allocates memory using .
The size and alignment must be a multiple of the large-page minimum. To obtain this value, use the function.
Reserves an address range that can be used to map (AWE) pages.